This little guy is slightly bigger than a 20x20 fc. You have to power it with 5v and it's super easy to do. You can use the 5vbec on any standard esc. For opto esc a separate bec will be required. I wired in a mamba 5v/9v bec because it's small, and I kept it in line with the esc so it's neat. I soldered a xt60 with a cap. The only miss I could find other than no documentation was the 5v power! You'd think they would have it so you can power direct voltage. I haven't used it yet but plan on putting this in something soon. In the picture you will see how I wired in my 5vbec and connected it to the board. If your trying to figure out the Batt/ Esc situation, it looks like that is kept separate from the rest of the board. Almost like a pdb but only dealing with the battery and esc that's it. Thanks BG for the fast delivery!!

This little guy is slightly bigger than a 20x20 fc. You have to power it with 5v and it's super easy to do. You can use the 5vbec on any standard esc. For opto esc a separate bec will be required. I wired in a mamba 5v/9v bec because it's small, and I kept it in line with the esc so it's neat. I soldered a xt60 with a cap. The only miss I could find other than no documentation was the 5v power! You'd think they would have it so you can power direct voltage. I haven't used it yet but plan on putting this in something soon. In the picture you will see how I wired in my 5vbec and connected it to the board. If your trying to figure out the Batt/ Esc situation, it looks like that is kept separate from the rest of the board. Almost like a pdb but only dealing with the battery and esc that's it. Thanks BG for the fast delivery!!

This little guy is slightly bigger than a 20x20 fc. You have to power it with 5v and it's super easy to do. You can use the 5vbec on any standard esc. For opto esc a separate bec will be required. I wired in a mamba 5v/9v bec because it's small, and I kept it in line with the esc so it's neat. I soldered a xt60 with a cap. The only miss I could find other than no documentation was the 5v power! You'd think they would have it so you can power direct voltage. I haven't used it yet but plan on putting this in something soon. In the picture you will see how I wired in my 5vbec and connected it to the board. If your trying to figure out the Batt/ Esc situation, it looks like that is kept separate from the rest of the board. Almost like a pdb but only dealing with the battery and esc that's it. Thanks BG for the fast delivery!!

It is perfect! So tiny and enough options for a simple fpv plane or a sub 250g build. https://youtu.be/OC3Z7mtg-Ps << video! Cant add anynore pics dont know why...

It is perfect! So tiny and enough options for a simple fpv plane or a sub 250g build. https://youtu.be/OC3Z7mtg-Ps << video! Cant add anynore pics dont know why...

It is perfect! So tiny and enough options for a simple fpv plane or a sub 250g build. https://youtu.be/OC3Z7mtg-Ps << video! Cant add anynore pics dont know why...

Good quality product I really liked it. I'll get myself another one.

Good quality product I really liked it. I'll get myself another one.

Good quality product I really liked it. I'll get myself another one.

More to my Youtube channel : MrSalvoFly.

More to my Youtube channel : MrSalvoFly.

More to my Youtube channel : MrSalvoFly.

More to My Youtube channel: MrSalvoFly.

More to My Youtube channel: MrSalvoFly.

More to My Youtube channel: MrSalvoFly.

https://youtu.be/H3oo3vHEDT8

https://youtu.be/H3oo3vHEDT8

https://youtu.be/H3oo3vHEDT8

Very good product. Good stabilization. Easy to setup via osd. You need a fpv monitor or googles to configure It. Tested with sbus input and MAV2 telemetry. Everithing works good. Perfect stabilization and RTH on a 600 mm sub 250g airplane.

Very good product. Good stabilization. Easy to setup via osd. You need a fpv monitor or googles to configure It. Tested with sbus input and MAV2 telemetry. Everithing works good. Perfect stabilization and RTH on a 600 mm sub 250g airplane.

Very good product. Good stabilization. Easy to setup via osd. You need a fpv monitor or googles to configure It. Tested with sbus input and MAV2 telemetry. Everithing works good. Perfect stabilization and RTH on a 600 mm sub 250g airplane.

a few spares while they were cheap

a few spares while they were cheap

a few spares while they were cheap

I finale got the replacement in as the 2nd unit osd chip or something when. This is a great board from what I've read. The board is delicate and you need to make sure you don't have and solder joints. So on this Fc I cut down the pin end so they are almost flush. I spread Flux on the pins this time not the board. The solder will flow! Next instead of soldering long leads. I soldered a xt60 directly to the board. I also soldered a separate power lead for cam/vtx as they are both above 5v operating power. Next I solder another xt60 to the esc side for a PnP fc. Keep in mind again this fc is sensitive solder quick and don't leave the tip sitting too long.

I finale got the replacement in as the 2nd unit osd chip or something when. This is a great board from what I've read. The board is delicate and you need to make sure you don't have and solder joints. So on this Fc I cut down the pin end so they are almost flush. I spread Flux on the pins this time not the board. The solder will flow! Next instead of soldering long leads. I soldered a xt60 directly to the board. I also soldered a separate power lead for cam/vtx as they are both above 5v operating power. Next I solder another xt60 to the esc side for a PnP fc. Keep in mind again this fc is sensitive solder quick and don't leave the tip sitting too long.

I finale got the replacement in as the 2nd unit osd chip or something when. This is a great board from what I've read. The board is delicate and you need to make sure you don't have and solder joints. So on this Fc I cut down the pin end so they are almost flush. I spread Flux on the pins this time not the board. The solder will flow! Next instead of soldering long leads. I soldered a xt60 directly to the board. I also soldered a separate power lead for cam/vtx as they are both above 5v operating power. Next I solder another xt60 to the esc side for a PnP fc. Keep in mind again this fc is sensitive solder quick and don't leave the tip sitting too long.

easy enough to setup. osd clear to read.

easy enough to setup. osd clear to read.

easy enough to setup. osd clear to read.