mbogelund
Q: What are the dimensions of this; how big or small is it?
Asked by mbogelund on 2019-01-15 08:50:26
Q: What are the physical dimensions of these resistors - what length and diameter in mm?
Asked by mbogelund on 2020-02-28 01:00:51
Nico80 Hi! Highest diameter is 1.8mm, min is 1.2 in the middle. Length is 3.5mm. Standard 1:6w resistor size. My Fluke Dmm says the 1% tolerance is there!! 100k=100.0kohm Perfect!
2020-02-29 11:17:45 Helpful (1)Q: What is the diameter of the inlet nozzle?
Asked by mbogelund on 2017-12-21 02:15:52
BG478573815 I have ordered the ID 1848558 hot air gun ,will these fit this gun
2021-10-07 02:45:00 Helpful (1)Q: What are the outer diameters of the reduced end of the two reduction nozzles?
Asked by mbogelund on 2017-12-21 01:50:05
cleres tamanhodo conector: 35 mm
2021-09-11 07:10:20 Helpful (0)Q: Are they breadboard friendly?
Asked by mbogelund on 2017-12-06 02:53:33
fortwonator ifthey are breadboard compatible, the terminals are flexible.
2021-05-08 08:32:23 Helpful (0)Q: Will the output voltage stay the same even if I change the load on the output?
Asked by mbogelund on 2020-07-22 08:20:22
OGHagen Most buck converters when used within limits keep the output voltage pretty well assuming the load increase slowly. A sudden increase in load will usually cause a drop in voltage. However the load vs no-load drop may be significant, so make sure to adjust with a light load. That's what the theory teach us anyways. In practice you will probably see a drop in voltage on the output if you increase the load. How much depends on the load.
2020-09-06 08:17:12 Helpful (1)
mbogelund Compro uno de estos y llegado. Si no llega, puedes enviar una reclamacion, y vas a tener tu dinero.
2020-02-27 05:15:29 Helpful (0)Q: what is maximum depth measured by this?
Asked by himanshusharma0 on 2019-04-18 01:55:35
mbogelund That's not how it works, it's not a distance sensor. It doesn't measure the distance from where it's installed to where the water surface is. It measures whether there is water where it's installed or not. So you can for example install it below normal water level and get a message when the water level drops below that point, or install it above normal water level and get a message when the water rises to that point.
2020-02-27 05:09:27 Helpful (0)We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
.jpg)
babapro31 width 10cm excluding wheel
2022-05-14 02:45:43 Helpful (0)