Customer Reviews

4.74 out of 5
See all 72 reviews
Write a Review
  • All Reviews (72)
  • Image (6)
  • Video (0)
  • All Star
    • All Star(72)
    • 5 Star(62)
    • 4 Star(2)
    • 3 Star(7)
    • 2 Star(1)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (New Zealand)
|
Show Original

A part of the review has been auto-translated.

  • 18/02/2016

    Habe 2 Stk bestellt. Die Kabelisolierung ist etwas steif, aber Temperaturfest. Die 100kOhm kommen gut hin. Einer der beiden Thermistoren war schon mal in Verwendung weil das Gewinde und das Gehaeuse generell Gebrauchsspuren aufwies.

    Comments
    Show Original
  • 29/01/2019

    perfect item

    Comments
    Show Original
  • 10/08/2017

    My favorite thermistors for E3D...

    Comments
    Show Original
  • 02/06/2018

    Not tested yet but looks good :)

    Comments
    Show Original
  • 11/05/2017

    very good ;) Thanks

    Comments
    Show Original
  • 10/09/2018

    Ordered 3 of these to replace standard glass bead sensors and installed first one in my Maker Select V2 and it lasted 2 hours into a 5 hour print and bead sensor that is glued into the m3 brass housing came loose and popped out of the brass insert which caused machine to fail. Lucky I had updated firmware to include thermo protection or machine would have just kept trying to head extruder head until it burned out heater or caught fire.

    Comments (1)
    Show Original
  • 24/07/2020

    Easy to use and requires only simple marlin recompile + PID calibration. Unfortunately : even with correct thermistor, the sensors underrate the real temperature by ~20 degrees in my case (180 degrees provide the same results as 200C before with my ender3 original sensor) . Easy to compensate tho, so no biggie :)

    Comments
    Show Original
  • 03/07/2017

    Plug and play upgrade for the Wanhao i3 v2.1. Bought it as an upgrade to the stock thermistor. It's a little more accurate, but not by much. The main reason to buy this however is the fact that it screws into place, unlike the stock thermistor which is held in with a washer and a screw. This is both not good looking and strains the wires. With this, it looks much cleaner and safer. The wires are also better than the stock ones. Just don't bend them too much.

    Comments
    Show Original
  • 09/01/2016

    I purchased three since the price was so good! M3 thread works great with both heat blocks that I've tried so far. This is a kit that includes 2 female JST connectors and the female housing. The brass connection is solid unless you try to be he-man and bond the stud permanently into the heat block via brute force. Do not attempt, it will result in the permanent bonding of just the stud and not the thermistor. Great buy and banggood is dang good!

    Comments
    Show Original
  • 28/02/2018

    I'm looking forward to installing this on my hot-end when I get it. The pre-installed disconnect is very handy if you have to take apart your hot-end

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$4.15
    • US$3.99
    • US$8.51
    • US$7.99
    • US$65.99
    • US$12.90
    • US$11.35
    • US$16.09
    • US$14.35
    • US$14.99
    • US$31.99
    • US$5.74
    • US$297.85
    • US$2.09
    • US$435.85
    • US$420.00
    • US$3.99
    • US$9.50