All Messages

Q: Are these metric or imperial ?

Asked by Keith on 2023-01-03 08:12:36

BG414861525 hi Keith, Please look at the description; those numbers can not be in inches, those drill bits would be huge. also there is no mention of fractions or anything that comes usually with imperial measures. cheers!

2023-01-03 08:32:58 Helpful (0)
Submit
Answers (4)

BG451844845 FN = EN Which is the ENABLE Signal to run & stop the motor. CW = DIR Which is change of DIRECTION Signal. CLK = PLS Which is the CLOCK or PULSE Signal to set the speed of the motor. These are all input signals from your controller (separate device), These are NOT the Motor connections, which are A+, A- and B+, B- for the two motor windings (or four windings joined in series or parallel, to become two).

2021-12-31 04:53:30 Helpful (0)
Submit
Answers (3)

BG414861525 it's a 220v single phase input. it's clearly written.

2020-12-09 12:14:05 Helpful (0)
Submit
Answers (2)

BG414861525 hi, this converts a 2 phases 220v current into 3 phases 220-340v that some powerful electrical engines need. through selecting the right wires you can choose if output is 220 or 340v. I use it for the engine of my old but strong metal lathe.

2020-05-03 03:55:00 Helpful (0)
Submit
Answers (1)

Q: Can this be used vertically ?

Asked by auroreboreale on 2020-04-25 06:55:20

BG414861525 Hello, I don't know what amount of side load you plan to put on the bearings (which would be the result of a vertical position with the rotation axis being horizontal), but that was also my intention when I bought mine, so, looking at how they are built, I bought 2 of them and they are bolted together with some pre-load pressure to prevent any deviation on the axis due to the load. Pay attention however that the whole plate is made of a cheap cast aluminium, not even a billet turned in a lathe, so putting too much weight on the axis will have the steel bearings damage the aluminium when they turn, eventually locking it. It's fine to turn a glass plate for a table, something like that, but putting it vertical, the more the center of gravity of the weight is distant from your bearings, the more momentum it creates on it to break it. Be wise :)

2020-04-25 12:09:06 Helpful (1)
Submit
Answers (1)

Q: My internal mic is not working. How do I test this?

Asked by Ewan on 2020-02-27 01:13:54

BG414861525 what made you assume that there is an internal microphone ? There is a plug for one mic on the top left corner of the front face, and you can also pair a phone with bluetooth; any of those could be used. microphone line if you want to use an ipod or external MP3 player, and phone to perform calls using the car speakers. The product doesn't have its own microphone, it needs be connected.

2020-02-27 03:41:40 Helpful (0)
Submit
Answers (2)

BG414861525 the title says 2.2is, this is your answer! you should check if your spindle is 3phased then yes, if spindle is 1 phase then you need nothing.

2020-02-19 07:39:05 Helpful (0)
Submit
Answers (1)

BG414861525 no pokemon, and list of games is too long to list here (hundreds)

2020-02-19 07:37:13 Helpful (0)
Submit
Answers (1)

BG414861525 i don't know the Hyundai Island but I know the Megan 2; the dashboard is curved, this device is not curved. also Renault Megane 2 has a 1 DIN height radio CD player. please see this item title clearly indicates 2DIN in height, 7 inch diagonal. try to imagine if your car can fit a 7 inch diagonal, this will give you the answer by yourself (for Megane 2, obviously it is NO).

2020-02-19 07:36:01 Helpful (0)
Submit
Answers (3)