All Messages

Q: Dies this fit MN D90?

Asked by BG533221181 on 2021-04-29 05:50:58

BG322490502 Most likely not

2021-11-20 11:28:08 Helpful (0)
Submit
Answers (2)

Berty Depends on the width between your chassis rails and motor size.

2021-08-29 01:26:40 Helpful (1)
Submit
Answers (2)

Q: do these fit front and back ?

Asked by RAWR on 2021-09-16 07:07:08

carbonhugger yesthey do just need a couple of tiny pieces of double sided tape then u can remove later

2021-10-02 11:17:28 Helpful (0)
Submit
Answers (1)

Q: Will these fit the SCX24?

Asked by RAWR on 2021-09-16 04:25:00

MrRopret I don’t have scx24. But I think it will not fit.

2021-09-28 01:04:33 Helpful (1)
Submit
Answers (1)

Q: do these fit the Chevy C10 model?

Asked by RAWR on 2021-09-14 05:52:16

BG114742383 they will fit most 1 16th scale cars

2021-09-21 12:54:57 Helpful (0)
Submit
Answers (1)

Q: do these fit the front and back?

Asked by RAWR on 2021-09-16 07:14:29

BG114742383 yes it comes as a set of 4 for front and back

2021-09-21 12:54:02 Helpful (0)
Submit
Answers (1)

Q: do these fit both the front and the back?

Asked by RAWR on 2021-09-16 07:13:29

ScotRC Yes they do

2021-09-20 11:27:49 Helpful (0)
Submit
Answers (1)

BG351163548 A diferença de medida entre ele e o outro é apenas na altura ,coisa pouca ,coisa de meio centímetro. Ele também é 6500 kv ,igual o original ,mas ele tem mais força e uma ventilação melhor !!

2021-09-13 05:06:51 Helpful (0)
Submit
Answers (1)

Q: can you put the original pinion gear on this ??

Asked by RAWR on 2021-09-11 08:35:58

en_srl Measure original shaft diameter and if it is 1.5mm then yes. But you must be accurate as it could break. You might want to check where you can buy a replacement gear - just in case.

2021-09-11 11:32:30 Helpful (0)
Submit
Answers (1)

Q: what size gear do I need for on the motor pinion ?

Asked by RAWR on 2021-08-25 01:35:28

Berty 15-25 tooth

2021-08-29 01:29:06 Helpful (1)
Submit
Answers (1)

BG533221181 Hey. I used one of the plastic bearings out of the stock diff as a spacer. I filed it to the right size to get the best mesh. Also eliminating as much left to right movement in the axle is helpful I used washers at the end of the axle between the housing and the hex end for the tyre to fit to. Hope this all helps.

BG533221181 25/04/2021
1
Comments (3)

Q: dimensions ?

Asked by RAWR on 2021-05-01 03:47:08

Kokken no measure

2021-05-13 09:39:50 Helpful (0)
Submit
Answers (1)

Q: does this fit mn45?

Asked by BG533221181 on 2021-04-29 03:47:32

Sempiternal not sure

2021-05-08 05:11:41 Helpful (0)
Submit
Answers (1)

Q: will this fit the MN range 90,99,45?

Asked by BG533221181 on 2021-04-29 04:20:09

Astacology WAIT FOR DETAILS

2021-05-08 04:35:27 Helpful (0)
Submit
Answers (1)

Q: Does this fit the MN D90?

Asked by BG533221181 on 2021-04-29 05:48:58

Ekstrom_ no

2021-05-08 04:25:03 Helpful (0)
Submit
Answers (1)