Customer Reviews

4.66 out of 5
See all 32 reviews
Write a Review
  • All Reviews (32)
  • Image (4)
  • Video (0)
  • All Star
    • All Star(32)
    • 5 Star(27)
    • 4 Star(2)
    • 3 Star(1)
    • 2 Star(1)
    • 1 Star(1)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (New Zealand)
|
Show Original

A part of the review has been auto-translated.

  • 28/10/2019

    Bought this as a spare part for an Ender 3 Pro. Fits well, but slightly lower quality than stock hot end. Note that it is with the older type heat block (different product pictures), so it can be a bit tricky fitting the glass thermistor correctly to get precise temperature measurements. It is not a problem for me, though, as I already have a newer type heat block, which I intend to use. It can be done, but larger encapsulated thermistors would be better suited for this. Price is slightly high considering the quality and the type of heat block.

    Comments
    Show Original
  • 05/05/2020

    looks like it'll do as a good backup. here's hoping the inner coating will hold up. other than that it looks well made.

    Comments
    Show Original
  • 09/07/2019

    arrivé à temps, fonctionne bien

    Comments
    Show Original
  • 13/12/2019

    epico salu2 de Bolivia

    Comments
    Show Original
  • 13/02/2020

    O boy does this thing look pretty, but like a crazy girlfriend they can look really nice, just remember you have to live with them. I can't even say $7 is worth it, I would rather burn the money in a fire pit, I have spent way more than what I saved, in time, trying to get this thing to work right. and that is after waiting 1.5 months to get it. 1. This is not an all metal hot end. There is a ptfe tube in it, that doesn't even line up right. If you want a crash course in how to unclog a hot end, boy golly buy this thing, youll be an expert by then tenth time you do it. 2. The glass thermistor comes in a plastic bag, that's shipped in a paper parcel. Mine didn't make the trip. and was broken on arrival the usual -14 temperature symbol on the ender 3 announced this luckily before I ran the line through the jacket. No big I have another one. 3. The brass nozzle one this "all metal hot end" is short. SHORT. so if you have an upgraded or printed carriage I hope it doesn't rely on a standard length nozzle. 4. This leaky SOB will put pla above and below the hot end. make sure you tighten the "all metal" ptfe tube holder tightly to the block, even then you may get a nice batch of goo on the top of the block. 5. The J connector is not the standard one for ender 3, youll either ahve to unclip the current one and unpin it. or jam the individual pins into your board, i recommend the former. I can't believe I am complaining about a chinese hot end, cause I knew what I was getting into. Do not buy this, I would rather take a chance on some Wish shoes, than do this again. What a total piece of caca. if you do decide to run this gauntlet look up some videos on how to properly place a thermistor before you put this one in if you haven't before, God Speed.

    Comments (1)
    Show Original
  • 27/06/2019

    With incredible timing, this arrived on the exact day that the hot end on my Creality Ender 3 decided to spew molten plastic all over the heat exchanger and nozzle block. I installed it using the existing thermocouple and cartridge heater and it works fine. Be warned, though, that this unit is about 3/16" shorter than the stock one on my Ender 3 and necessitated raising the bed. If you then go back to the stock hot end, don't forget to lower the bed again to avoid bad things happening.

    Comments
    Show Original
  • 05/09/2020

    It look fine. I have not tested it, as it is for emergency spares. I do like that there are grub screws to secure the heater cartridge and the thermistor, and that these can be fitted from the left or the right.

    Comments
    Show Original
  • 05/12/2020

    Excellent quality build , have not tried printing with it yet as my extruder at this time is working very well.

    Comments
    Show Original
  • 07/03/2019

    Exactly what was ordered, thank you for the red color as that will look really great on the printer I'm building!

    Comments
    Show Original
  • 01/03/2019

    Montato su Alfawise U20, funziona perfettamente con PETG. La stampante è diventata più "sensibile" alle "irregolarità" del piano di stampa.

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$16.72
    • US$10.99
    • US$18.39
    • US$13.40
    • US$16.99
    • US$16.09
    • US$56.19
    • US$6.39
    • US$3.09
    • US$5.74
    • US$249.99
    • US$31.99
    • US$23.99
    • US$1.69
    • US$3.09
    • US$297.85
    • US$251.85
    • US$85.99