Customer Reviews

4.95 out of 5
See all 101 reviews
Write a Review
  • All Reviews (101)
  • Image (1)
  • Video (1)
  • All Star
    • All Star(101)
    • 5 Star(96)
    • 4 Star(5)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (New Zealand)
Show Original

A part of the review has been auto-translated.

  • 06/12/2017


    Show Original
  • 26/03/2021

    product corresponds to the image, the product could be packaged somewhat better because it is fragile but well recommended seller

    Show Original
  • 13/05/2021

    It's not compatible with my copter, even though it's the same model.

    Show Original
  • 29/03/2021

    Have not got it yet

    Show Original
  • 04/09/2013

    Received my new pcb after 2 weeks, actually after checking the release date from my country custom then I know that the postman is culprit making a slow delivery. For about 300 km distance they need whole week to reach my home and I don't know why. Anyway this new pcb is highly recommended for those who want to buy pcb for their v912 cos it straight away bind with the tx and for the camera and function that is a bonus but I still haven't try it yet. Overall this will be a better choice if you want to buy pcbfor v912.

    Comments (1)
    Show Original
  • 08/05/2016

    на старой плате гироскоп сошел сума верт постоянно крутился в одну сторону ,триммирование и все остальное не помогало решил заказать эту плату и все, теперь все суппер!

    Show Original
  • 28/06/2014

    Arrived in 10 days, easy to install: only 2 cables to solder. Worked and binded at first attempt... what else ? I installed it on version 1 off V912 Heli & it works fine as expected. Antenna allreadi installed on mine. IT's worthy bying it if your model is in ggod statement > PS: i configured my Turnigy 9X in PPP "Model Heli 1"... V912 became a so easy to fly Heli due to TR9X radio quality. To bind to 9x: switch model on first, push (maintain) turnigy binding back button while truning TX on... wait for ref heli light to slow down, turn T9X off then on again... servos will twitch... that's done > you can flight.. Enjoy :-)

    Show Original
  • 15/04/2014

    Hay que soldar un par de cables pero funciona perfecto, si teniais la primera version vereis que esta placa es un poco diferente, pero funciona perfectamente. Cambiar la placa entera solo si falla la sincronizacion con el mando, en caso de que falle algunos de los rotores solo hay que cambiar e triax correspondiente, no hace falta cambiar toda la placa.

    Show Original
  • 07/04/2017

    This board is for a spare part . In the past something will happen and you either have a spare or you wait for one to replace the one that is defective . (You can use the board on an old V912 receiver you just can't use the accessories that the new V912 has. The original V912transmitter will bind to it. I have not tested the receiver and hope it is not defective. I know if there are any problems Banggoods will make it good.

    Show Original
  • 07/12/2015

    I purchased this to replace an earlier version board that had burnt out due to a new pilot leaving the throttle halfway up when the heli was sideways on grass and the blades were blocked which caused electrical energy to store up and overheat the ESC portion of the PCB. The removal and replacement was very easy. Just be sure not to mix up any of the plugs. Take a picture or close up video if you have to before disassembling. The solder portion of the installation was also very easy since it is in an easy to reach spot. After installing, no issues, the board works just like new.

    Show Original

    Total 0 pages

    Go to page


    You might be interested in

    recommendation for you
    • US$1.60
    • US$18.76
    • US$2.93
    • US$35.21
    • US$13.99
    • US$4.72
    • US$65.54
    • US$80.49
    • US$14.94
    • US$15.48
    • US$10.99
    • US$4.59
    • US$21.99
    • US$5.99
    • US$4.99
    • US$13.58
    • US$2.78
    • US$7.12