Customer Reviews

4.98 out of 5
See all 54 reviews
Write a Review
  • All Reviews (54)
  • Image (10)
  • Video (1)
  • All Star
    • All Star(54)
    • 5 Star(53)
    • 4 Star(1)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (New Zealand)
|
Show Original

A part of the review has been auto-translated.

  • 15/09/2016

    Use Mosfet : Alpha & Omega Semiconductor AON7702A 30V 36A Nch Power MOSFET. I used the F3 EVO FC (ID:1064058). Connect the 1s 3.7V battery to PWM8 + - Port, supplying power to the Micro motor driver from PWM7 + - Port. PWM1 ~ 4 signal line connected to each other. In Cleanflight Configurator CLI, and is set to motor_pwm_rate = 16000 (2000 or more at a minimum), No problem at all, quad Copter fuselage of the brush motor (gear drive) was flying. I think this is a very interesting item. Thanx Banggood!

    Comments (1)
    Show Original
  • 02/05/2018

    отличная маленькая платка для коллекторных моторчиков поставил в связке с emax femto на tiny whoop все замечательно работает

    Comments (2)
    Show Original
  • 18/10/2017

    I'm using this card for DIY projects not at all for quads but to control motors, lights, pumps... in my RC models.

    Comments
    Show Original
  • 25/10/2018

    thank you

    Comments
    Show Original
  • 31/08/2017

    I'm using this board for the FETs in my RC models. It's small, light weight and the PCB is already made. You can control motors, relays, LEDs... at any voltage since the ground is commuted.

    Comments
    Show Original
  • 05/02/2017

    I intend to use this with naze32fc, then to connect some coreless motors, Just for fun to try if it will work. Its a really small board, just as described. Thanks Banggood,

    Comments
    Show Original
  • 16/09/2016

    I've bought this sweet little board to use it as a small and lightweight 6 channel power switch for my RC and maybe a some experiments with the pwm output from my Arduinos or X5C-1 with CC3D Atom. However, it would be nice to know the max working voltage espacially for switch using.

    Comments
    Show Original
  • 09/01/2019

    I'm using it in my models to drive motors, LEDs, relays: https://www.youtube.com/watch?v=6XvVSZfSMNQ&list=PLqb9x7UiIO9SHp1dG2-tX6dv9Ku4KeowZ&index=10&t=2s

    Comments (1)
    Show Original
  • 02/12/2016

    I was not sure if this had speed controller features or was just FET based. It is a relatively simple FET based board that does not take a servo style input. It requires a full PWM form 0 to 100%, (servos signals are something like 3-6%). The flight controller will need to be in brushed motor mode to work with this board. (I have used it with an ATTiny85) It is rated at 10A. I've not run it at that but I did accidently short the output and it seams to survive that. (350mAh 1s). Has diodes and I think a cap across motors so seams a good design. Should be good for Arduino projects too where you want up to six single direction DC motors. Great value. Should be 6*s.

    Comments
    Show Original
  • 10/03/2021

    Works as expected

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$7.77
    • US$91.99
    • US$28.74
    • US$13.79
    • US$21.84
    • US$6.89
    • US$18.39
    • US$11.99
    • US$18.39
    • US$50.02
    • US$43.69
    • US$95.99
    • US$24.14
    • US$91.99
    • US$57.99
    • US$80.49
    • US$21.38
    • US$5.74