At Banggood, we uses cookies and other similar technologies to provide you with essential functionalities and for aggregated statistics.
We also use optional cookies for a better experience with:
You can choose not to allow some types of cookies via"Cookie Settings".If you want to learn more about it, you can swipe to the bottom of the page to see the Privacy Policy
When you visit any website, it may store or retrieve information on your browser, mostly in the form of cookies. This information might be about you, your preferences or your device and is mostly used to make the site work as you expect it to. The information does not usually directly identify you, but it can give you a more personalized web experience.
Because we respect your right to privacy, you can choose not to allow some types of cookies. However, blocking some types of cookies may impact your experience of the site and the services we are able to offer.
{{$productInfo.reviewAmount.average}} out of 5
Note: The camera mount for Gopro show on the photo is not Included. This version comes with Yellow.
After our very popular 3inch Cinematic EVA bumper BumbleB and Green Honet CineWhoop series, we were trying to increase performance and reduce weight for an even better and longer flight experience for a wide variety of use.
Our all new 3.5inch project is finally ready for all you content creators or those guys who like to wear some protection every now and then. Prop protection is what we're talking about here...
ProTek is not necessarily just a Cinewhoop series but far more. Equipped with our all new 2203.5 motors for more power and less heat. We were able to increase speed and thrust by 50% compared to it's 3inch predecessor which gives a lot more room for a lot more fun. Our GPS measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a for Gopro but also do some loaded punch outs or light freestyle moves.
A lot of thought was put into the different assembly options. Our stock BNF will ship in the standard configuration but you can either do a pusher mod (flip the build upside down) or a lite mod (remove the protective plastic for weight optimization).
Durable plastic protectors with copper standoffs, portable compact design, easy accessable UBS port without disassembly, LED battery status, lost model buzzer and a universal for GoPro TPU for a full size or naked for GoPro. If you wanna go extra light, get one of our 5V balance plug for GoPro power cables to get rid of the internal battery.
Need a naked for GoPro case or mount? Checkout our new iFlight naked for GoPro Hero8 TPU case to use with your ProTek35.
Features:
- UPGRADED PROP GUARDS V2.0 (Material optimized)
*No Props or frame in view!
*High performance True-AIO Board Beast Whoop F7 AIO 45A to save weight and space
*T700 Quality Carbon (40% more tensile strength compared to common 3K carbon)
*Lightweight one-piece frame design (Less flexibility, more Rigid, more Durable)
*Low Resonance frame construction (Less Jello, more Cinematic footage)
*Nebula Nano Digital HD System
*Butter smooth 2203.5 3600KV (4S)
*Pre-tuned with smooth freestyle settings
PRE-TUNED & PRE-SETUP:
Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!
To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"
Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!
Please check our linked article on "How to disable Angle-Mode, activate Acr0 -Mode"
ProTek35 BNF Specs:
*Board Beast Whoop F7 AIO 45A
*Motor: XING 2203.5 3600KV (4S)
*Wheelbase: 151mm
*Body Size: 118*94.5mmmm
*Bottom plate thickness: 3.5mm
*Top plate thickness: 2mm
*Top and bottom plate spacing: 20mm (aluminum standoff height)
*Propeller size: 3.5 inch
*FC pattern: 25.5*25.5mm / 20*20mmmm
*FPV cam spacing: 20mm
*Weight: 348.3g (without battery)
ProTek35 HD Quad BNF Included Components and Parts
pre-built and tested Quadcopter
1 x ProTek35 Frame
1 x DJI FPV Camera
1 x DJI FPV Air Unit Module
2 x DJI FPV Air Unit Antenna SMA
1 x TPU Bracket for DJI Air Unit Module
1 x TPU Antenna holder for DJI antenna
2 x Nazgul 3535 propeller (Set of 4 - Color May Vary)
1 x iFlight Lipo Strap 15*150mm (Color May Vary)
1 x iFlight Lipo Strap 15*250mm (Color May Vary)
1 x for GoPro TPU bottom stand black (for GoPro Protector not included)
FC // Beast F7 AIO
MCU: BGA-STM32F745
Gyro: MPU6000
UARTs: 5
Blackbox: 8Mb Onboard Flash
BEC output: 5V 2.5A
Barometer: BMP280
Connector: Micro-USB
OSD: AT7456E
FC Firmware:IFLIGHT_F745_AIO
Mounting pattern: 25.5*25.5mm φ3mm
Dimensions: 32.5*32.5mm
Weight: 8.5g
ESC // 45A 2-6S
*Current Sensor: Yes
*Input: 2-6S LIPO
*Current scale: 200
*Constant: 45A / Burst: 50A
*BLHeli: BLHeli-S
*RPM-Filter ready: Yes (JazzMaverick or JESC firmware)
*Telemetry: no
*ESC Firmware: BlheliS G-H-30
*Mounting pattern: 25.5*25.5mm/Φ3mm
Important
The DJI Remote Controller is recommended for beginners since you won't need to set up another receiver, but it is also optional in this BNF drone because it is NOT required in order to use the FPV system. If you don't choose to use the DJI Remote Controller, you can choose a receiver option for your transmitter and then bind to your own radio as usual.
Shipping method(s) | Shipping time | Tracking information |
---|