Customer Reviews

4.95 out of 5
Write a Review
  • All Reviews (64)
  • Image (9)
  • Video (0)
  • All Star
    • All Star(64)
    • 5 Star(61)
    • 4 Star(3)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (New Zealand)
|
Show Original

A part of the review has been auto-translated.

  • 24/02/2021

    I got a version with a 4 pole terminal block. It was well packed and undamaged. The active heatsink does not have support from the bottom of the PCB. So the PCB is bent by the heat sink pressure. It will probably need another heatsink with support. The power supply has a thin and short cable to the mains. After a short use, the source became quite hot. There is also a blue LED inside the source indicating operation, which is not visible. But when measuring the original source, he was able to supply 1.6A at 11.96V (load powered by another source). This is more than is written on the cover. The connection to the mobile phone using the E-test application was successful. He saves the measurement results in a table, which pleased me. Otherwise, the application is not user-friendly.

    Comments
    Show Original
  • 11/04/2021

    It's a lovely product. The battery's internal resistance, the heat voltage, the pulled ampere, the drawn watt value, many more of the values are instantaneous. It can test up to 180 watts.

    Comments (2)
    Show Original
  • 06/05/2021

    The product does not give label current. 18A stays. Those who receive will review accordingly

    Comments
    Show Original
  • 25/08/2020

    Be carefull its DL24 not DL24P that post in photo the seller. I am very dissapointing with this. Be aware dont buy if you want this in photo.

    Comments
    Show Original
  • 29/03/2021

    Excelente producto. recomendado 100% La entrega fue rapida y en excelentes condiciones.

    Comments
    Show Original
  • 06/02/2021

    Looks good. Haven't tested yet. Fast shipping.

    Comments
    Show Original
  • 06/07/2020

    Received in Romania after 15 days by EU Priority Line. Package was intact, inside unit without any damage. Tested and is working perfect. As a bonus from measuring power, voltage and current, can also measure ambient or body temperature with sensor supplied. Function is a little bit intuitive. The scanning of the bar code was impossible, some erasure on the picture. I have downloaded app for Android from app shop (E-meter) and is working. Not connected to computer yet, but for the moment everything was working so far.

    Comments
    Show Original
  • 20/05/2020

    Arrival took long but I blame the Corona for it :-) The tester was well packed, both a sturdy cardboard box and a blister pack. A quick test shows that the tester is working as it should. Bluetooth and computer connections not yet tested. The UI could perhaps be a little more intuitive but you'll learn it quick. Build quality seems good, I think this is a good tester, gives me all the information I need.

    Comments
    Show Original
  • 08/06/2020

    Appears to be good quality. Works well so far. Menu and setup is just maze - anything but intuitive. The Android app is sort of useless to easy the setup. Video on YouTube suggests that it does not run on 180W - probably the max is about 150W.

    Comments
    Show Original
  • 10/01/2021

    This device is very good and accurat in terms of current and Voltage regulation. BUT: 1.The cut off voltage should be with an accuracy of a minimum of two digits after the decimal point, not only one! You have 4 decimals on the Display, so its possible to change the software to show the point to the mid position. So you get 2 decimals after the point and 2 decimals before the point which is very important for single cells. May be it is also possible to use 3 decimals after the point as long you are under 9.99V but this will be not so important. If you have more than 99,99V on the Display the decimalpoint should automaticaly jump one position to the right from mid position of the 4 digits to get "100.0V" in the Display. 2. If you want to change the cut off voltage it will take ages to come from 4V Dc to 60V DC, the change speed is so low that you fall asleep next to your device! May be the PC software can be made better to direct input the new voltage value to the devicejQuery11130976002861393953_1610272670374? Or / and speed up the change speed of the Buttons of the device. 2. If the power plus clamp spring of from your battery (60V Battery) during you have enabled the DL24P and you reconnect it without switching off the Device before, you burn the Mosfet! The DL24P do not reconize the wire break in the current lane and will drive the Mosfet to maximum power because no current will goes trough if the cable is disconnected and only the small messuring cable will remain on the battery. If you then reconnect the current lane without switching of the device, you will burn the MOS! 3. I think the inner resistant messuring is useless, it currently shows only fantasy values and not real values also I did not see any funktion to callibrate it. Repair it or remove it from the Firmware and if you remove it then use the free space on the LCD for other usefull things.

    Comments (1)
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • NZD$7.02
    • NZD$174.54
    • NZD$5.01
    • NZD$5.01
    • NZD$10.04
    • NZD$10.19
    • NZD$56.82
    • NZD$14.56
    • NZD$7.05
    • NZD$130.41